Products – technoadhesives.com

#441 ZERO VOC FOAM PRIMER

wfcadmin — Wed, 06 Jul 2022 09:54:35 +0000

BASE:	Resin Modified Rubber
SOLVENT:	Acetone
COLOR:	Clear, Red, Green
CONSISTANCY:	Medium Thin Liquid, Brookfield 1/20 220 CPS ± 30 CPS @ 70˚F
SOLIDS:	% by Weight 17% ± 2%
SPECIFIC GRAVITY:	7.0 ± .2 Lbs./Gallon
APPLICATION:	Most methods may be used but due to the fast drying, spray application is recommended. Apply primer to achieve a dry film thickness of 1-2 mils. If corrosion is a problem increase thickness to 3-4 mils dry film. It may be necessary to clean the skin surface prior to primer application. Allow all solvent to evaporate prior to foaming. Spray Atomization Pressure 15 – 20 PSI Fluid Pressure 10 – 15 PSI
COVERAGE:	Square Foot/Gallon 300 – 400, Sprayed
CAUTION:	FLAMMABLE, keep away from sparks and open flames. Avoid prolonged contact with skin or breathing of vapors. Provide adequate ventilation.
All statements, technical information and recommendations contained herein are based on tests we believe to be reliable, but the accuracy thereof is not guaranteed, it being specifically understood that there are no warranties either expressed or implies incident to the sale of this product. No person is authorized or empowered to make any statement or recommendation concerning said product not contained herein, and any such statement or recommendation so made shall not bind the company. Users assume all risk and liability whatsoever resulting from the use of this product and must confirm the adaptability thereof by their own tests.

TECHNO ADHESIVE SYSTEM NO. 98/99

wfcadmin — Wed, 06 Jul 2022 09:47:47 +0000

Techno epoxy adhesive system #98/99 has been formulated especially for bonding steel leveling plates to concrete. The resin #98 should be thoroughly mixed in equal volume with its hardener, #99 just prior to use. The unmixed resin and hardener has a shelf life in excess of one year. In gallon quantities, the mixed adhesive has a working life of one to two hours. A thin film will cure overnight and gain strength with time, developing a final strength of about 3000 psi, far in excess of the concrete. This material mixes and applies well. From our tests, adhesion is good with a minimum of floor preparation. If the concrete is in good condition, not contaminated with grease or oil and does not have a sealer or surface coating, dirt and dust removal is all that is required. If there is a sealer or surface coating, this should be removed through grinding. Heavy deposits of oil or grease should be removed using detergents or solvents. If solvent is used, allow adequate time for the solvent to evaporate before applying the epoxy for bonding. The plates can be cleaned through sand blasting or the use of solvents for the removal of contaminants. Normally the epoxy is applied to the clean floor, the plate applied, and then the weight of the machine is lowered into position so the excess adhesive is squeezed out. Should you wish to remove the bond, the usual method is to heat the metal and the bond with a torch to destroy the adhesive while applying a sharp blow to the edge of the plate. This material is supplied in one gallon cans, five gallon pails and fifty-five gallon drums. The minimum order is one gallon #98 and one gallon #99.

TECHNO ADHESIVE NO. 355 AEROSOL WEB SPRAY FLEXIBLE FOAM ADHESIVE LOW VOC

wfcadmin — Wed, 06 Jul 2022 09:42:03 +0000

This is a spray applied flexible foam cement for bonding all types of foams to themselves and various substrates, such as cloth, wood, or metal. It has excellent application characteristics including quick tack, high coverage and high strength bonds. It produces soft non-dimpling bonds which will not harden or darken with age. Fabrics in contact with this bond line will not become stained after aging for long periods even when exposed to sunlight. The adhesive provides a low VOC formulation, with a limit of 34% by weight in its aerosol form. The adhesive is heat resistant to 200 degrees Fahrenheit.

TECHNO ADHESIVE NO. 155 AEROSOL WEB SPRAY FLEXIBLE FOAM ADHESIVE

wfcadmin — Wed, 06 Jul 2022 09:39:16 +0000

TECHNO ADHESIVE NO. 199 NON FLAMMABLE CONTACT CEMENT

wfcadmin — Wed, 06 Jul 2022 09:34:39 +0000

BASE:	Resin Modified Rubber
SOLVENT:	Chlorinated Hydrocarbon
COLOR:	Clear, Red, Green, Black
CONSISTANCY:	Medium Thin Liquid, Brookfield 1/20 250 CPS + -50 CPS @ 70˚F
SOLIDS:	% by Weight 21% ± 2%
SPECIFIC GRAVITY:	10.3 ± .2 Lbs./Gallon
APPLICATION:	Most methods may be used, but due to the fast drying spray application is recommended. Binks 63 fluid tip, 66SA air cap, 30-40 psi fluid, 40-50 psi atomization.
CAUTION:	Avoid prolonged contact with skin or breathing of vapors, Provide adequate ventilation.
All statements, technical information and recommendations contained herein are based on tests we believe to be reliable, but the accuracy thereof is not guaranteed, it being specifically understood that there are no warranties either expressed or implies incident to the sale of this product. No person is authorized or empowered to make any statement or recommendation concerning said product not contained herein, and any such statement or recommendation so made shall not bind the company. Users assume all risk and liability whatsoever resulting from the use of this product and must confirm the adaptability thereof by their own tests.

TECHNO ADHESIVE #122 ASSEMBLY WOOD GLUE

wfcadmin — Wed, 06 Jul 2022 09:27:57 +0000

TYPE:	Polyvinyl Acetate Emulsion
VISCOSITY:	6000 CPS + or – 500 Cps.
SOLIDS:	46 + or – 1
pH:	4.5 – 5
POUNDS PER GALLON:	9.4
APPLICATION:	Approximately 45 pounds of glue per 1000 feet of single glue line. This may vary, depending on the porosity of the substrates. Use enough glue to produce a light squeeze out along the glue perimeter. Open assembly periods should not exceed 12 minutes at 70 degrees Farenheit. Laminates should be stored a minimum of 4 hours before cutting or sanding, with an optimum time of 24 hours.
All statements, technical information and recommendations contained herein are based on tests we believe to be reliable, but the accuracy thereof is not guaranteed, it being specifically understood that there are no warranties either expressed or implies incident to the sale of this product. No person is authorized or empowered to make any statement or recommendation concerning said product not contained herein, and any such statement or recommendation so made shall not bind the company. Users assume all risk and liability whatsoever resulting from the use of this product and must confirm the adaptability thereof by their own tests.

TECHNO ADHESIVE #259 EASY SPRAY FLEXIBLE FOAM ADHESIVE NON-FLAMMABLE

wfcadmin — Wed, 06 Jul 2022 09:15:43 +0000

BASE:	Synthetic Elastomer
SOLVENT:	Blend
COLOR:	Clear, Red or Green
CONSISTANCY:	Medium Thin Liquid, Brookfield 2/20 = 450 ± 50 CPS
SOLIDS:	By Wt. = 35 ± 1% by Volume = 40 ± 1%
SPECIFIC GRAVITY:	9.8 ± .2 LBS./GAL.
APPLICATION:	Spray Atomization Pressure: 15 – 30 PSI Fluid Pressure: 5 – 10 PSI Binks 66SS Fluid Nozzle: 66SS Air Cap or Equal
COVERAGE:	400 – 600 Sq.Ft./Gal.
CAUTION:	Avoid prolonged breathing of vapors and excessive contact with skin; use with adequate ventilation.
All statements, technical information and recommendations contained herein are based on tests we believe to be reliable, but the accuracy thereof is not guaranteed, it being specifically understood that there are no warranties either expressed or implies incident to the sale of this product. No person is authorized or empowered to make any statement or recommendation concerning said product not contained herein, and any such statement or recommendation so made shall not bind the company. Users assume all risk and liability whatsoever resulting from the use of this product and must confirm the adaptability thereof by their own tests.

TECHNO ADHESIVE NO. 159 HVP EASY SPRAY FLEXIBLE FOAM ADHESIVE NONFLAMMABLE

wfcadmin — Wed, 06 Jul 2022 09:08:05 +0000

BASE:	Synthetic Elastomer
SOLVENT:	Medium Thin Liquid (Brookfield 1/20 = 350 ± 50 cps.)
COLOR:	Clear, Red or Green
CONSISTANCY:	Blend of Chlorinated Solvents, Contains No ODC’s
SOLIDS:	By Weight: 25 ± 1%, By Volume: 30 ± 1%
SPECIFIC GRAVITY:	10.3 ± .2 Lbs./Gal.
APPLICATION:	Spray atomization pressure 15-30 psi. Fluid pressure 5-10 psi. Binks 66SS fluid nozzle: 66ss air cap or equal.
COVERAGE:	400-600 sq.ft./gal.
CAUTION:	Avoid prolonged breathing of vapors and excessive contact with skin. Provide adequate ventilation when applying.
All statements, technical information and recommendations contained herein are based on tests we believe to be reliable, but the accuracy thereof is not guaranteed, it being specifically understood that there are no warranties either expressed or implies incident to the sale of this product. No person is authorized or empowered to make any statement or recommendation concerning said product not contained herein, and any such statement or recommendation so made shall not bind the company. Users assume all risk and liability whatsoever resulting from the use of this product and must confirm the adaptability thereof by their own tests.

TECHNO ADHESIVE NO. 155 EASY SPRAY FLEXIBLE FOAM ADHESIVE

wfcadmin — Wed, 06 Jul 2022 09:05:29 +0000

BASE:	Synthetic Elastomer
VISCOSITY:	Ketone Aliphatic Hydrocarbon Blend
COLOR:	Clear, Red or Green
CONSISTANCY:	Medium Thin Liquid, Brookfield 1/20 300 CPS @ 70˚F
SOLIDS:	% by Weight 41% ± 2%
SPECIFIC GRAVITY:	6.7 ± .2 Lbs./Gallon
APPLICATION:	Spray Atomization Pressure 10 – 20 PSI Fluid Pressure 5 – 10 PSI
COVERAGE:	Square Foot/Gallon 400 – 600
CAUTION:	This cement is flammable. Keep away from sparks and open flames. Provide adequate ventilation.
All statements, technical information and recommendations contained herein are based on tests we believe to be reliable, but the accuracy thereof is not guaranteed, it being specifically understood that there are no warranties either expressed or implies incident to the sale of this product. No person is authorized or empowered to make any statement or recommendation concerning said product not contained herein, and any such statement or recommendation so made shall not bind the company. Users assume all risk and liability whatsoever resulting from the use of this product and must confirm the adaptability thereof by their own tests.

TECHNO ADHESIVE NO. 133 L INSULATION ADHESIVE (NONFLAMMABLE)

wfcadmin — Wed, 06 Jul 2022 08:50:19 +0000

BASE:	Modified Acrylic Emulsion
VISCOSITY:	Brookfield #4 @ 20 rpm = 500 – 200 cps
SPECIFIC GRAVITY:	Lbs./Gal. 9.0 ± .1
SOLIDS:	51± 1%
SOLVENT:	None
EQUIPMENT:	Spray; Fluid Nozzle, Binks 66SS or Equal @ 20-30 psi Atomization Cap; Binks 66SFF or Equal @ 40-60 psi
COVERAGE:	600 – 750 Sq.Ft./Gal.
TEMPERATURE RANGE:	-30˚F to 300˚F WATER/MOISTURE RESISTANCE: Excellent
CLEAN UP:	While still wet (white) water; After set up (clear) solvents; 1,1,1 trichlorethane, methylene chloride or toluene.
CAUTION:	Surfaces should be clean, dry, and free from oil or grease. Use with adequate ventilation
All statements, technical information and recommendations contained herein are based on tests we believe to be reliable, but the accuracy thereof is not guaranteed, it being specifically understood that there are no warranties either expressed or implies incident to the sale of this product. No person is authorized or empowered to make any statement or recommendation concerning said product not contained herein, and any such statement or recommendation so made shall not bind the company. Users assume all risk and liability whatsoever resulting from the use of this product and must confirm the adaptability thereof by their own tests.